• ADDRESS:
  • 1324 S. Flower St
  • Los Angeles, CA 90015
  • Tel: 213.663.1400

STORE HOURS:

Follow us on Instagram!

Mon - Fri 11:00AM - 4:00PM

 Sat 11:00AM-3:00PM

Closed Sunday

 

 

Original Store ! Carpe Diem:

3820 Valley Blvd Suite i, Walnut, CA 91789

Close
Search

Proxxon Percision Lathe PD 250/E

For face, longitudinal and taper turning, thread-cutting. For machining steel, brass, aluminium and plastic. Mounting flange for fastening the mill/drill head PF 230. Centre distance 250mm (10"). Swing 70mm (2 3/4"). Height over cross slide 43mm (1 11/16").

Machine bed made of cast iron, wide-legged prismatic guide. Rear flange for mounting the mill/drill head PF 230. With additional speed control (full-wave electronics) continuously adjustable to 100 - 300 or 1,000rpm, depending on belt ratio. And change gears for left-hand and righthand threads of the most important metric pitches (0.5 - 0.625 - 0.7 - 0.75 - 0.8 - 1 - 1.25 - 1.5mm). High quality 3-jaw chuck as per DIN 8386 Class 1 (concentricity tolerance 0.04mm (0.002") . Capacity through reversing jaws from 2 - 75mm (5/64" - 3"). Including lathe chuck guard with safety shutdown.

 PX34002

  • For vibration-free work even at high loads
  • Headstock and tailstock of die-cast aluminium
  • Bed carriage made of die-cast zinc 
  • Quiet DC special motor with 3-stage belt drive for 300 - 900 and 3,000rpm
  • Handwheels made of aluminium, with adjustable scale ring (1 division = 0.05mm (.002"), 1 revolution = 1mm (3/64")
  • Covered lead spindle

 

 

Be Advised :
Other extra accessories not included

 

Splash guard and chip collecting tray
Made from 1.5mm (1/16") thick sheet metal, powder coated. Bevelled edges at the front and back allow slight cleaning. Mounting hole and raised base to secure lathe are pre-drilled.

PX24008

 

Fixed steady for longer work pieces

Especially for boring. Also required if the tailstock cannot be used to "counter". Up to Ø 40mm.

PX24010

 

Centre turning attachment. For highest accuracy with high rotational precision.

This includes: 1 face plate, 2 fixed centres (MT 2 and MT 1/short) and 1 drive dog. Packed in a wooden box.

PX24014

 

Professional gear chuck with MT1

For the tailstock of the PD 250/E. Capacity up to 10mm (3/8").

PX24020

 

Additional quick change tool holder (separately)

Can be used with the above above-mentioned quick change tool post.

PX24024

 

Quick change tool post 

For quick tool change and easy height adjustment. Includes 2 tool holder elements.

PX24026

 

4-jaw chuck with independent jaws
For clamping angular and asymmetrically shaped work pieces. Capacity up to 80mm (3,1"). Chuck Ø 75mm (3").

PX24036

 

Collet set with ER 20 collets: For extreme true concentric accuracy. 2 - 10mm (5/64" - 25/64").
For high precision machining of round parts. The collet set is mounted instead of the lathe chuck. With 8 collets (2 - 2.5 - 3 - 4 - 5 - 6 - 8 and 10mm). Packed in a wooden box.

PX24038

 

Dividing attachment TA 250

For accurate machining of circular work pieces (e.g. production of gear wheels). Supplied with two dividing discs (40 and 48 teeth), enabling standard divisions of 2 - 3 - 4 - 5 - 6 - 8 - 10 - 12 - 16 - 20 - 24 - 40 and 48. The taper of the dividing attachment is the same size as that of the main spindle of the PD 250/E lathe, thus 3 jaw chuck (to be ordered separately under NO 24 034) and 4 jaw chuck (NO 24 036) may be mounted. Horizontal fitting (e.g. on the cross-slide of the lathe) and vertical fitting (on the machine bed) are possible. With matching nuts and screws for fixation in MICROMOT standard T-slots 12 x 6 x 5mm (15/62" x 15/64" x 3/16"). Supplied in a wooden box with sliding lid.

PX24044

 

Radius Cutting Attachment

Mounted on the cross slide in place of the tool holder. For producing convex and concave shapes, for turning radii or 3/4 spheres up to max. 32mm. Height adjustable tool holder (boring tool tip adjustable from 30 through 45mm above cross slide) for use with FD 150/E, PD 250/E, PD and older PROXXON lathes. Dimensions: base plate 67 x 50mm, height 55mm. Complete with finishing cutter 8 x 8 x 80mm. In wooden box with sliding lid.

PX24062

 

Die Holder for round dies, threads M 3 to M 10

Sizes: M 3 - 4 - 5 - 6 - 8 - 10. The straight shank 13/32" fits our drill chuck NO 24 020 when mounted in the tailstock of the PD 250/E. The holder is held by hand while cutting the threads. Comes in a wooden box.

PX24082

 

Tool Holder for rotary tools. For use on lathe machines

This holder allows mounting of our rotary tool IBS/E (collar size 20mm (4/5")) to the tool post of the Lathe PD 250/E for grinding or polishing purposes.

PX24098

 

14-piece parallel supports set

Ground in pairs. For adjusting work on drilling machines, lathes and milling machines. Made of high-alloy, hardened steel (58 - 62 HRC). Parallel accuracy 0.002mm. 2 each of 8 x 10, 15, 20, 25, 30, 35 and 40mm. Length 100mm. Packed in a wooden box.

PX24266

 

HSS Boring Tool Set

One each cutter for 60 degree (metric) and 55 degree (Whitworth) inside threads, 1.3mm (3/64"), 2.65mm (7/64") and 4mm (5/32"). Shank: 6mm (15/64"). Length: 95 mm (3 3/4"). The cutters are held by a tool holder that mounts to the tool post of the PD 250/E. Comes in a wooden box.

PX24520

 

Five Piece Cutting Set

8 x 8 x 80mm (5/16" x 5/16" x 3 9/64"). One each roughing out, parting, finishing cut, left and right cutter. Made from high-quality Cobalt HSS, pre-ground. Packaged in a wooden box.

PX24530

 

Three Piece Thread Cutting Set

6 x 8 x 80mm (15/64" x 5/16" x 3 9/64"). One cutter for external thread (ground to 60°, metric), one for internal thread, one general cutting. Made from high-quality Cobalt HSS, pre-ground. Packaged in a wooden box.

PX24540

 

Cutter Set with tungsten inserts

Three holders (5/16" x 5/16" x 3 35/64"), for roughing out, finishing cuts and boring bar, holes from 15/32". Standard tungsten tips, 55°, plated. Three additional inserts, securing screws and key TX8 are included.

PX24555

 

Tungsten Disposable Tips

For the holders 24 555. Ten piece set.

PX24557

 

Three Piece Center Drill Set

HSS, 60°. Complete set with sizes of 2, 2.5 and 3.15mm (5/64", 3/32", 1/8"). Made from high-quality Cobalt HSS, pre-ground. Packaged in a wooden box.

PX24630

 

Gear Set for turning standard / imperial threads

Contains 8 change gears for making threads with 56, 48, 42, 36, 35, 30, 28, 24, 21, or 18 thread pitch per inch.

PX34011